נמכר



כל יחידה הינה מגבר כוח רב ערוצי עצמאי
בנייה מאסיבית, מחברים מוזהבים, תו תקן THX, צלעות קירור חזיתיות וספק טרואידי גדול

כל מגבר מוציאה בהתנגדות של 8 אום 60 W לכל אחד מששת הערוצים
או 70 W לכל ערוץ בהפעלה של רק חמישה ערוצים מתוך השישה
לעומת זאת במצב של גישור כל יחידה מוציאה בהתנגדות של 8 אום כבר 150 W עבור כל אחד משלושת הערוצים הפעילים

מוצר יד שניה במצב שמור מאוד

מידע טכני
Model | RMB-1066 |
Power Configurations | 6 x 60 Watts 3 x 150 Watts Bridged |
Watts/Channel all channels driven, unbridged, 8 ohm load, 20 - 20 kHz, 0.06% THD |
60 watts - - |
THD (20 - 20kHz) cont. rated power one-half rated power one watt per channel |
- 0.03% maximum 0.03% maximum 0.05% maximum |
Intermodulation Distortion (60 Hz: 7 kHz, 4:1) |
0.03% maximum |
Frequency Response | 15 Hz - 100 kHz (±1dB) |
Damping Factor (20 - 20,000 Hz, 8 ohms) |
150 |
Input Overload Level | 5V |
Signal to Noise Ratio (IHF A network) |
116 dB |
Input Impedance/Sensitivity | 1.5 V, 22 kohms |
Power Requirements: | 115 volts, 60 Hz (U.S. version) 230 Volts, 50 Hz (European version) |
Power Consumption: | 700 Watts |
Dimensions (W x H x D): | 430 x 121 x 435 mm 16 15/16 x 4 3/4 x 17 1/8 inches |
Weight (net): | 13.5 kg, 29.75 lbs. |

מידע מהחברה
The RMB-1066 multi-channel power amplifier is an enormously flexible unit intended primarily for use in surround systems and delivers high power in a variety of configurations.
The power supply and output circuits are configured for exceptional reserve capability and stability.
In six channel mode, the RMB-1066 delivers 60 watts RMS each (20 Hz to 20 kHz @0.03%THD into 8 ohms).
In five channel mode (one channel quiescent), power increases to 70 watts RMS each measured by the same demanding standards.
Amplifier pairs can be bridged to develop 150 watts x 3 for almost half a kilowatt of output power.
Three rear panel switches (one two-way and two three-way) make bridging easy and also link the inputs via internal "daisy chain " connections with a single source, thus simplifying system wiring.
Input level controls, strategically placed between front panel heat sink fins and an extensive 6 LED indicator array ease system adjustment and monitoring.
12 volt trigger operation and a detachable IEC power cord directly address demanding custom installation requirements while custom brass speaker terminals provide full contact power transfer.

התאמה
הגברה טרנזיסטורים עם אופי קריר
מתאימה לשילוב בסט הזקוק לריענון כגון:
סאונד עכור, באס נמרח, מפוזר, גבוהים לא חדים
מחייה רמקולים עם נצילות נמוכה מ 87 db ו/או התנגדות בעייתית הנמוכה מ 8 אום
מצב
מוצרי יד שניה
נמכר